Adhesion of tooth fragment after trauma: effect of adhesion strategy and storage in the rescue box.

This study aims to investigate the impact of storage conditions for crown fragments (specifically, whether they were stored within a tooth rescue box or in tap water) on their adhesion to fractured teeth when subjected to two different adhesive systems (namely, total etch and self etch). Sixty maxillary premolars were sectioned to obtain tooth fragments. These fragments were stored briefly (2 hours) and reattached in the following groups: Group 1 (fragments stored in tooth rescue box and reattached with etch and rinse (E&R) technique), Group 2 (fragments stored in tap water and reattached with E&R technique), Group 3 (fragments stored in tooth rescue box and reattached with self-etch (SE) technique), and Group 4 (fragments stored in tap water and reattached SE technique). After reattachment, the bonded tooth fragments underwent thermal cycling (500 cycles, 5-55 °C) and bond strength testing using a universal testing machine. Two-way Analysis of Variance (ANOVA) and Tukey's tests were used for bond strength comparison (p ≤ 0.05). A two-parameter Weibull distribution was conducted to evaluate the reliability of the storage medium and adhesion modality on bond strength. The results showed that measured shear bond values (MPa ± Standard deviation (SD); arranged in descending order) for each group were: Group 2 (Tap water/E&R = 6.5 ± 2.1), Group 1 (Rescue box/E&R = 6.0 ± 2.5), Group 4 (Tap water/E&R = 5.1 ± 2.8), and Group 3 (Rescue box/SE = 3.6 ± 3.2). Significant differences were found only between Groups 2 and 3 (p = 0.002). In conclusion, storing crown fragments in a tooth rescue box did not significantly affect the shear bond strength of the restored tooth. However, fragments reattached using the self-etch technique showed comparable shear bond strength but a higher rate of adhesive failures compared to the E&R technique.

Characterisation of experimental flowable composites containing fluoride-doped calcium phosphates as promising remineralising materials.

OBJECTIVE: Remineralising composites with antibacterial properties may seal the cavity and prevent secondary caries. This study aimed at developing experimental flowable composites containing different concentrations of fluoride-doped calcium phosphate fillers and evaluating their remineralising and antibacterial properties. METHODS: Experimental resin-based composites containing different concentrations (0-20 %) of fluoride-doped calcium phosphate fillers (VS10/VS20) were formulated. The release of calcium (Ca), phosphate (PO) and fluoride (F) ions was assessed for 30 days. Remineralisation properties were evaluated through ATR-FTIR and SEM/EDX after storage in simulated body fluid (SBF). The metabolic activity and viability of Streptococcus gordonii was also evaluated through ATP, CFU and live/dead confocal microscopy. The evaluation of specific monomer elution from the experimental composites was conducted using high-performance liquid chromatography (HPLC). RESULTS: The composites containing VS10 showed the highest release of Ca, those containing VS20 released more F over time (p < 0.05), while there was no significant difference in terms of PO ions release between the groups (p > 0.05). A quick 7-day mineral precipitation was observed in the tested composites containing VS10 or VS20 at 10 %; these materials also showed the greatest antibacterial activity (p < 0.05). Moreover, the tested composites containing VS10 presented the lowest elution of monomers (p < 0.05). CONCLUSIONS: Innovative composites were developed with low monomers elution, evident antibacterial activity against S. gordonii and important remineralisation properties due to specific ions release. CLINICAL SIGNIFICANCE: Novel composites containing fluoride-doped calcium phosphates may be promising to modulate bacteria growth, promote remineralisation and reduce the risk of cytotoxicity related to monomers' elution.

Effect of antioxidants on adhesive bond strength to bleached enamel.

OBJECTIVE: To evaluate the influence of antioxidants (ATX) resveratrol, winter's bark, green tea and yerba mate on the bond strength between bleached enamel and the nanohybrid composite resin. METHODOLOGY: Bovine incisor crowns (n = 132) were randomly divided into 22 groups (n = 6) according to the application times (5, 10, 15, 30, and 60 min) of each antioxidant. Teeth restored without previous bleaching or ATX constituted the non-bleached control group (NB Ctrl) (n = 6), and teeth restored after bleaching and without ATX represented the bleached control group (B Ctrl) (n = 6). The 35 % hydrogen peroxide was applied for 45 min (3 application of 15 min) to the buccal enamel surface. ATX was used after bleaching for the specified time of each group and removed with air-water spray. The enamel was etched with 37 % phosphoric acid (30 s) and rinsed with air-water spray. The adhesive resin was applied to the enamel dry surface. Teeth were restored using 1 mm composite resin increments (10 × 10 × 3 mm) and sectioned in test specimens of 6 mm in length and 1 mm2 in cross-sectional area submitted to microtensile bond strength test (0.5 mm/min). The load (N) at failure was recorded, and the bond strength (σt) was calculated (MPa). The fracture area was analyzed under optical microscopy, and failures were classified as cohesive, mixed, or adhesive. Data was evaluated by Kruskal-Wallis and Dunn tests (p ≤ 0.05). RESULTS: B Ctrl group presented lower σt than NB Ctrl (p < 0.001). Applying resveratrol for 5 or 10 min, winter's bark for 10 or 15 min, green tea for less than 15 min, and yerba mate for 15 min provided similar σt between bleached enamel and nanohybrid composite to the control group. CONCLUSION: Restorative procedures performed immediately after tooth bleaching compromises adhesion. Experimental antioxidants applied to bleached enamel can increase the immediate bond strength of restorations performed directly after bleaching, with similar values to those observed in unbleached enamel. CLINICAL SIGNIFICANCE: This study presents promising results to support the use of antioxidants on the recently bleached enamel to allow adhesive tooth restorations. The immediate bonding obtained using antioxidants was similar to the one achieved in non-bleached enamel in brief application times. Green tea extract and resveratrol were able to restore the bond strength to bleached enamel in a short application time of 5 min. The reduction in the required application time holds the potential to decrease the overall duration of the clinical section, offering clinical advantages and improving the feasibility of using antioxidants on the bleached enamel prior to adhesive procedures.

Mechanical and Antimicrobial Properties of Boron Nitride/Methacrylic Acid Quaternary Ammonium Composites Reinforced Dental Flowable Resins.

Dental resin composites (DRCs) are commonly used to restore teeth affected by dental caries or defects. These materials must possess excellent properties to withstand the complex oral environment. The objective of this study was to prepare and characterize Boron nitride nanosheets (BNN)/ dimethyl amino hexadecyl methacrylate (DMAHDM) composites (BNN/DMA), and to evaluate them as functional fillers to enhance the mechanical and antimicrobial properties of dental resins. The BNN/DMA composites were successfully prepared under the theoretical guidance of molecular dynamics (MD), and then the physicochemical and morphological characterization of the BNN/DMA composites were carried out by using various test methods, such as FT-IR, XRD, UV-vis spectroscopy, SEM, TEM, and AFM. It was doped into the dental flowable resin in a certain proportion, and the results showed that the flexural strength (FS), elastic modulus (EM), compressive strength (CS), and microhardness (MH) of the modified resin composites were increased by 53.29, 47.8, 97.59, and 37.1%, respectively, with the addition of 0.8 wt % of BNN/DMA composite fillers. It has a good inhibition effect on Streptococcus mutans, with an inhibition rate as high as 90.43%. Furthermore, this effect persists even after one month of aging. In conclusion, the modification of flowable resins with low-concentration BNN/DMA composites favorably integrates the mechanical properties and long-term antimicrobial activity of dental resins. At the same time, they have good biocompatibility and do not affect the aesthetics. The BNN/DMA composite modified flowable resin has the potential to become a new type of antimicrobial dental restorative material.

A low-shrinkage-stress and anti-bacterial adherent dental resin composite: physicochemical properties and biocompatibility.

Polymerisation shrinkage and biofilm accumulation are the two main problems associated with dental resin composites (DRCs) that induce secondary caries, which can cause restoration failure. Polymerisation shrinkage can lead to microleakage gaps between the tooth and the DRCs, causing the aggregation of bacteria and development of secondary caries. Reducing the shrinkage stress (SS) and improving the resistance to bacterial adhesion have always been the focus of this field in modifying DRCs. A thiol-ene resin system can effectively reduce the polymerisation SS via its step-growth mechanism for delaying the gel point. Fluorinated compounds can reduce the surface free energies, thereby reducing bacterial adhesion. Thus, in this study, a range of mass fractions (0, 10, 20, 30, and 40 wt%) of a fluorinated thiol-ene resin system were added to a fluorinated dimethacrylate resin system/tricyclo decanedimethanol diacrylate to create a fluorinated methacrylate-thiol-ene ternary resin matrix. DRCs were prepared using the obtained ternary resin matrix, and their physical and chemical properties, effect on bacterial adhesion, and biocompatibility were investigated. The results demonstrated that the volumetric shrinkage and SS of the DRCs were reduced with no reduction in conversion degree even after the thiol-ene resin system was added. All DRC-based fluorinated resin systems exhibited an excellent anti-bacterial adhesion effect, as evidenced by the colony-forming unit counts, live/dead bacterial staining, and crystal violet staining tests against Streptococcus mutans (S. mutans). The genetic expressions associated with the bacterial adhesion of S. mutans were substantially affected after being cultured with fluorinated DRCs. All fluorinated DRCs demonstrated good biocompatibility through the in vitro cytotoxicity test and live/dead staining images of the L-929 cells. The above results illustrate that the DRCs based on the fluorinated methacrylate-thiol-ene resin matrix can be potentially applied in clinical practice due to their low SS and anti-bacterial adhesion effect.

Antimicrobial dental composites with K18-methyl methacrylate and K18-filler.

OBJECTIVE: To determine the effects of using K18-methyl methacrylate (K18-MMA) and K18-Filler on composite cure, esthetic, mechanical, polymerization shrinkage, and antimicrobial properties. METHODS: K18-MMA (0-20% w/w) was used to replace TEGDMA in a 70:30 Bis-GMA:TEGDMA composite filled to 70% w/w with barium glass or K18-Filler. Composite degree of cure (Rockwell15T hardness and near Infrared FTIR), hydrophilicity (contact angle measurements), translucency (transparency parameter measurements, TP), mechanical (3-point bend test), polymerization shrinkage (volumetric shrinkage and shrinkage stress), and antimicrobial properties (colony counting assay) against Streptococcus mutans, Streptococcus sanguinis, and Candida albicans were determined. RESULTS: All experimental groups had comparable degrees of cure (near Infrared FTIR and Rockwell15T Hardness), TP, moduli, polymerization volumetric shrinkages and shrinkage stresses to those of controls (Bonferroni corrected p > 0.0018). Only one group (15% K18-MMA+K18-Filler) had significantly different (lower) contact angles as compared to that of controls (Bonferroni corrected p < 0.0018). Most of the K18-Filler-containing composites had significantly lower ultimate transverse strengths (UTS) than controls (Bonferroni corrected p < 0.0018). Controls had significantly greater S mutans colony counts than 15% and 20% w/w K18-MMA+K18-Filler groups, and greater S sanguinis and C albicans colony counts than K18-containing groups. Of the composites with that provided significant antimicrobial properties against S. mutans, S. sanguinis, and C. albicans, only the 20% K18-MMA+K18-Filler group had significantly lower UTS than controls. SIGNIFICANCE: Composites with K18-MMA and K18-Filler with comparable physical properties to control composites and significant antimicrobial properties have been developed. K18-MMA and K18-Filler seem to be suitable for incorporation into commercial dental resins.

Epigallocatechin gallate-immobilized antimicrobial resin with rechargeable fluorinated synergistic composite for enhanced caries control.

OBJECTIVES: Given the global prevalence of dental caries, impacting 2.5 billion individuals, the development of sophisticated prevention filling materials is crucial. Streptococcus mutans, the principal caries-causing strain, produces acids that demineralize teeth and initiate dental caries. To address this issue, we aimed to develop a synergistic resin-based composite for enhancing caries control. METHODS: The synergistic resin composite incorporates fluorinated kaolinite and silanized Al2O3 nanoparticle fillers into an epigallocatechin gallate (EGCG) immobilized urethane-modified epoxy acrylate (U-EA) resin matrix, referred to the as-prepared resin composite. The EGCG-modified TPGDA/U-EA network was synthesized by preparing methacrylate-functionalized isocyanate (HI), reacting it with EGCG to form HI-EGCG, and then incorporating HI-EGCG into the TPGDA/U-EA matrix. The lamellar space within the kaolinite layer was expanded through the intercalation of acrylamide into kaolinite, enhancing its capability to adsorb and release fluoride ions (F-). The layered structure of acrylamide/ kaolinite in the U-EA resin composite acts as a F- reservoir. RESULTS: The physico-mechanical properties of the as-prepared resin composites are comparable to those of commercial products, exhibiting lower polymerization shrinkage, substantial F- release and recharge and favorable diametral tensile strength. The immobilized EGCG in the composite exhibits potent antimicrobial properties, effectively reducing the biofilm biomass. Furthermore, the synergistic effect of EGCG and fluorinated kaolinite efficiently counteracts acid-induced hydroxyapatite dissolution, thereby suppressing demineralization and promoting enamel remineralization. SIGNIFICANCE: Our innovative EGCG and fluoride synergistic composite provides enhanced antimicrobial properties, durable anti-demineralization, and tooth remineralization effects, positioning it as a promising solution for effective caries control and long-term dental maintenance.

Evaluating the effect of three fissure preparation techniques on microleakage of a colored flowable composite used as a fissure sealant.

Pit and fissure sealants play an essential role in preventive dentistry. This study evaluates the microleakage levels of a new and colored flowable composite applied as a sealant after three preparation techniques. A total of 24 non-carious mandibular permanent molars with deep pits and fissures were included in the study. Pit and fissures were prepared with 37% phosphoric acid, tungsten carbide bur and fissurotomy burs (SS WHITE Dental, New Jersey, USA) using conventional, enameloplasty and fissurotomy techniques. All samples were thermocycled following the placement of Rainbow Flow (PPH CERKAMED Wojciech Pawlowski, Poland) as a sealant and sections were taken after immersion in methylene blue dye. The microleakage levels of the samples were examined under a stereomicroscope (Olympus SZX-7 Olympus SZ-61 Stereo Microscope) at 2.8× magnification to analyze the dye penetration of the flowable composite. The 144 sections were examined and scoring for microleakage was done by examining the dye penetration from the occlusal border to the base of the fissure. Considering all sections regardless of the preparation technique, it was found that 16.6% of the sections have no leakage. Regarding the microleakage scores, the mean score of the conventional group was 1.87 ± 0.98, the mean score of the enameloplasty group was 1.88 ± 1.14, and the mean score of the fissurotomy group was 1.81 ± 1.1. The median scores of the conventional, enameloplasty and fissurotomy groups were 2, 2 and 1.5, respectively. The present study reports no difference between the microleakage level of a colored flowable composite material used as a pit and fissure sealant following three fissure preparation techniques and supports the clinical use of this material.

The effect of quaternary ammonium polyethylenimine nanoparticles on bacterial adherence, cytotoxicity, and physical and mechanical properties of experimental dental composites.

A significant problem related to the functioning of resin-based composites for dental fillings is secondary or recurrent caries, which is the reason for the need for repeated treatment. The cross-linked quaternary ammonium polyethylenimine nanoparticles (QA-PEI-NPs) have been shown to be a promising antibacterial agent against different bacteria, including cariogenic ones. However, little is known about the properties of dental dimethacrylate polymer-based composites enriched with QA-PEI-NPs. This research was carried out on experimental composites based on bis-GMA/UDMA/TEGDMA matrix enriched with 0.5, 1, 1.5, 2 and 3 (wt%) QA-PEI-NPs and reinforced with two glass fillers. The cured composites were tested for their adherence of Streptococcus Mutans bacteria, cell viability (MTT assay) with 48 h and 10-days extracts , degree of conversion (DC), water sorption (WSO), and solubility (WSL), water contact angle (CA), flexural modulus (E), flexural strength (FS), compressive strength (CS), and Vickers microhardness (HV). The investigated materials have shown a complete reduction in bacteria adherence and satisfactory biocompatibility. The QA-PEI-NPs additive has no effect on the DC, VH, and E values. QA-PEI-NPs increased the CA (a favorable change), the WSO and WSL (unfavorable changes) and decreased flexural strength, and compressive strength (unfavorable changes). The changes mentioned were insignificant and acceptable for most composites, excluding the highest antibacterial filler content. Probably the reason for the deterioration of some properties was low compatibility between filler particles and the matrix; therefore, it is worth extending the research by surface modification of QA-PEI-NPs to achieve the optimum performance characteristics.

The effect of zinc oxide (ZnO) nanoparticle concentration on the adhesion of mucin and Streptococcus mutans to heat-cured acrylic resin.

Incorporating zinc oxide (ZnO) nanoparticles as antibacterial fillers in heat-cured acrylic resin could decrease mucin and Streptococcus mutans (S. mutans) adhesion, reducing the incidence of dental caries in the baseplates of orthodontic patients. Here, ZnO nanoparticles were modified using 3-(trimethoxysilyl)propyl methacrylate with various concentrations, added to acrylic resin powder, homogenized, mixed with acrylic resin liquid, and processed. The composite systems interfered well with mucin and S. mutans adhesion. The lowest mean of the amount of mucin adhered was on heat-cured acrylic resin with 7.5% ZnO nanoparticles, with a standard deviation of 18.07±0.80 mg/mL. The ZnO nanoparticles with a concentration of 7.5% showed an 87.09±0.88% S. mutans adhesion in control groups with no additives. These composite systems were proven to have better physicochemical characteristics and antibacterial abilities. Combining ZnO nanoparticles with heat-cured acrylic resin has great potential for self-cleaning baseplates of orthodontic patients in the future.

Effect of composite resin containing antibacterial filler on sugar-induced pH drop caused by whole saliva bacteria.

STATEMENT OF PROBLEM: Secondary caries around restorations is a major problem and can be attributed to bacteria invading microgaps formed at the tooth-restoration interface. An antibacterial composite resin containing quaternary ammonium silica (QASi) filler has been reported to inhibit enamel demineralization in situ. However, whether the prevention of enamel demineralization by QASi-containing composite resin is because of the reduced metabolic activity of acid-producing saliva bacteria is unclear. PURPOSE: The purpose of this study was to compare the effects of QASi-containing composite resin and 2 other restorative materials on the viability of salivary bacteria and sugar-induced acid production. MATERIAL AND METHODS: Whole saliva from each of the 30 study participants, 14 at high risk and 16 at low risk for caries, was brought into contact with quadruplicate specimens of 3 restorative materials, Infinix Flowable Composite, an anti-bacterial composite resin containing 1.5% QASi filler (Nobio), Filtek Supreme Flowable Restorative (3M), a conventional flowable composite resin, and dental amalgam (Silmet). Bacterial growth and sugar-induced acid production on each restorative material were measured every 20 minutes for 18 hours. Caries risk groups were compared using the t test and repeated measures analysis of variance (α=.05). When significant, Bonferroni multiple comparisons were used. RESULTS: On average, the saliva with the QASi-containing composite resin specimens maintained a near-neutral pH, not dropping below pH 6.0. The saliva associated with both conventional restorative materials exhibited a pH drop below 5.5 (P<.001), the critical threshold for tooth demineralization according to the Stephan curve. Virtually no growth was measured on the surface of the antibacterial composite resin, whereas bacteria grew on the conventional composite resin and dental amalgam (P<.001). No differences were observed between participants at high and low risk of caries. CONCLUSIONS: Unlike amalgam and conventional composite resin, the QASi-containing composite resin showed a near-complete shutdown of the metabolic activity of salivary bacteria upon contact and virtually no bacterial viability. This suggests that the prevention of tooth demineralization by QASi-containing restoratives is associated with a significant reduction in bacterial metabolic activity.

Making graphene oxide (GO)-cladded SiO2 spheres (SiO2 @GO) as inorganic fillers for dental restorative resin composites.

OBJECTIVE: Graphene oxide (GO) is of great interest in dentistry as the functional filler, mainly owing to its ability to inhibit the formation of cariogenic bacteria and possess low cytotoxicity to different cells, such as human dental pulp cells, HeLa cells, etc. However, its typical brown color limits the practical application. METHODS: Here, the refractive-index-matched monodisperse SiO2 were used as the supporting substrates to synthesize GO-cladded SiO2 spheres (xSiO2 @ yGO) through a mild electrostatic self-assembly process, where x and y represent the amount of SiO2 and GO in the reaction mixture, respectively. The morphology and the optical performance of the obtained xSiO2 @ yGO particles were modulated by varying the mass ratio of SiO2 and GO (5:1, 10:1, 50:1, and 100:1). All developed hybrid particles were silanized and formulated with dimethacrylate-based resins. These were tested for curing depth, polymerization conversion, mechanical performance, in vitro cell viability, and antibacterial activity. RESULTS: Of all xSiO2 @ yGO materials, increasing the mass ratio to 100:1 made the 100SiO2 @GO particles appear light brown and possess the lowest light absorbance from 300 to 800 nm. The results of CIEL*a*b* system showed that all these hybrid particles exhibited obvious discoloration compared with SiO2 and GO, where 100SiO2 @GO possessed the smallest color difference. Furthermore, following the results of curing depth, polymerization conversion, and mechanical performance of dental composites, the optimal filler composition was 100SiO2 @GO at 5 wt% filler loading. The resultant 100SiO2 @GO-filled composite produced the highest flexural strength (115 ± 12 MPa) and the lowest bacterial concentration (6.7 × 108 CFU/mL) than those of the resin matrix (78 ± 11 MPa; 9.2 × 108 CFU/mL) and 5 wt% SiO2-filled composite (106 ± 9 MPa; 9.1 × 108 CFU/mL), respectively, without affecting in vitro cell viability. SIGNIFICANCE: The facile and mild synthesis of xSiO2 @ yGO hybrid particles provided a convenient way to tune their optical property. The optimal 100SiO2 @GO particles could be considered as the promising antibacterial filler to be applied in dental care and therapy.

A laboratory investigation on the effect of biguanide- and pyridine-derived antiseptics on the adhesion of resin composites to dentin.

Optimal bonding of adhesive restorations to dentin is crucial to prevent microleakage and enhance the survival of root-filled teeth. The aim of this study was to investigate the effect of chlorhexidine (CHX), alexidine (ALX) and octenidine dihydrochloride (OCT) on the bond strength of resin composites to coronal dentin. Human coronal dentin specimens were treated with 2% CHX, 0.1% ALX, 0.1% OCT or saline then restored with traditional or bulk-fill resin composites. The adhesion strength between the resin and dentin was measured using the microtensile bond strength and failure mode was determined using a stereomicroscope. Treatment with ALX and OCT resulted in significantly greater µTBS compared with CHX and saline, irrespective of the resin composite used. Alexidine treatment predominantly resulted in mixed failure, while adhesive failures were frequently observed in CHX and saline-treated dentin. In conclusion, final irrigation with ALX or OCT improved the bonding of resin composites to dentin.

Efficacy of bioactive materials in preventing Streptococcus mutans-induced caries on enamel and dentine.

The study investigated the ability of bioactive materials used to restore enamel and dentine specimens to prevent caries. Enamel (n = 50) and dentine (n = 50) specimens were obtained from bovine incisors, prepared, and randomly allocated to one of five groups according to the restorative treatment: alkasite without adhesive system; alkasite with adhesive system; high viscosity glass ionomer cement; resin composite; no restoration; negative control group. Specimens were restored, exposed to a thermal cycling aging protocol, sterilized, and exposed to a cariogenic challenge induced by Streptococcus mutans and then submitted to surface and subsurface microhardness tests and polarized light microscopy to verify the caries lesion development in enamel or dentine surrounding the restorative materials. Data were analyzed using one-way ANOVA. In enamel and dentine, glass ionomer cement, alkasite without and with adhesive system presented a lower percentage surface microhardness loss than resin composite and negative control. Enamel subsurface microhardness presented no statistically significant differences between glass ionomer cement, alkasite without and with adhesive system. Glass ionomer cement also did not present statistically significant differences from resin composite and the negative control. In dentine, glass ionomer cement showed the highest subsurface microhardness values. In conclusion, bioactive restorative materials provide greater protection to enamel and dentine against surface caries development than resin composite.

Effects of silica surface modification with silane and poly(ethylene glycol) on flexural strength, protein-repellent, and antibacterial properties of acrylic dental nanocomposites.

OBJECTIVE: The main aim of the current work was to develop dental acrylic-based composites with protein-repellent and antibacterial properties by using surface-modified silica nanoparticles. The effects of surface modification of silica nanoparticles in protein-repellent and antibacterial activity and mechanical properties of dental composites including flexural strength, flexural modulus, and hardness were discussed. METHODS: The surface of silica nanoparticles was first chemically treated with 3-methacryloxypropyltrimethoxysilane (MPS) as a coupling agent and then with poly(ethylene glycol) (PEG) bonded to MPS. Dental acrylic-based composites were prepared with mass fractions of 10, 15, 20, 30, and 40 % of PEG-modified MPS-silica nanoparticles (PMS). The chemical surface modification of silica nanoparticles with MPS and PEG was confirmed by Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). RESULTS: The dental composite containing 20 wt% PMS nanoparticles could reduce the protein adsorption by 28 % as compared with a composite containing 20 wt% MPS-modified silica. The antibacterial test indicated that the PMS nanoparticles can significantly reduce the adhesion of Streptococcus mutans and the biofilm formation on the surface of dental composites. It was found that the flexural strength increased by increasing the PMS nanoparticles from 0 to 20 wt% and then decreased by the incorporation of higher percentages of these nanoparticles. Also, with increasing the weight percentage of PMS nanoparticles, the elastic and the flexural modulus and the hardness of resin nanocomposites were increased. SIGNIFICANCE: In the current work, for the first time, dental resin composites containing PEG were prepared with excellent protein-repellent and antibacterial properties.

Bioactive Dental Resin Composites with MgO Nanoparticles.

Photoactivating dental resin composites have been the most prevailing material for repairing dental defects in various clinical scenarios due to their multiple advantages. However, compared to other restorative materials, the surface of resin-based composites is more susceptible to plaque biofilm accumulation, which can lead to secondary caries and restoration failure. This study introduced different weight fractions (1, 2, 5, 10, and 15%) of magnesium oxide nanoparticles (MgONPs) as antibacterial fillers into dental resin composites. Multifarious properties of the material were investigated, including antibacterial activity against a human salivary plaque-derived biofilm, cytotoxicity on human gingival fibroblasts, mechanical and physicochemical properties as well as the performance when subjected to thermocycling aging treatment. Results showed that the incorporation of MgONPs significantly improved the composites' anti-biofilm capability even at a low amount of 2 wt % without compromising the mechanical, physicochemical, and biocompatibility performances. The results of the thermocycling test suggested certain of aging resistance. Moreover, a small amount of MgONPs possibly made a difference in enhancing photoactivated polymerization and increasing the curing depth of experimental resin composites. Overall, this study highlights the potential of MgONPs as an effective strategy for developing antibacterial resin composites, which may help mitigating cariogenic biofilm-associated secondary caries.

Novel hydrolytic resistant antibacterial monomers for dental resin adhesive.

OBJECTIVES: To evaluate the properties of novel hydrolytic resistant antibacterial monomers and to determine the properties of resin adhesives containing these monomers. METHODS: Methacrylamide-based QAC (Quaternary Ammonium Compound) monomers, 1-(11-Methacryla-midoundecyl)pyridine-1-ium bromide (MAUPB) and 1-(12-Methacryl-amidododecyl)pyridine-1-ium bromide (MADPB), and their methacrylate-derivatives, N-(1-Methacryloylundecanyl)pyridinium bromide (MUPB) and N-(1-Methacryloyldodecanyl)pyridinium bromide (MDPB), were synthesized and characterized. The minimum inhibitory (MIC) and bactericidal (MBC) concentrations were determined against S.mutans and E.faecalis. Cytotoxicity of unpolymerized monomers were evaluated using L-929 and MDPC-23. Each monomer was incorporated into experimental resins (BisGMA/TEGDMA/CQ/EDMAB or BisGMA/HEMA/CQ/EDMAB) at 10wt%. FTIR Spectra were collected for degree of conversion (DC%) measurement. Bacterial attachment on resin disks were determined by fluorescent microscope. Mechanical properties of experimental resins were evaluated by flexural strength & modulus and shear bond strength testing. RESULTS: The antibacterial activity of MDPB≥MUPB>MADPB>MAUPB. The TC50 of MAUPB> MADPB>MUPB >MDPB. Incorporation of MAUPB in BisGMA/TEGDMA-based resin, had no significant effect on DC%, while significantly increase DC% in BisGMA/HEMA-based Resin. MUPB and MAUPB containing resins showed less viable bacterial attachment than pure resins. After 3-month storage, resins containing MAUPB illustrated higher flexural strength than their corresponding resins containing MUPB. BisGMA/HEMA-based resin containing MAUPB illustrated significantly higher resin-dentin shear bond strength than that of MUPB and pure resin. CONCLUSIONS: Methacrylamide monomer containing QAC, MAUPB, possessed antibacterial properties and superior physical and mechanical properties when incorporated in resin adhesives as compared to their corresponding methacrylate monomer, MUPB. CLINICAL SIGNIFICANCE: Methacrylamide-based QAC monomers are potentially used to formulate antibacterial hydrolytic resistant resin adhesives and enhance resin-dentin bond strength.

Surface properties and Streptococcus mutans biofilm adhesion of ion-releasing resin-based composite materials.

OBJECTIVE: To evaluate the adhesion of Streptococcus mutans (S. mutans) and related surface properties of ion-releasing resin-based composite (RBC) restorative materials. METHODS: Two ion-releasing RBCs, Activa (ACT) and Cention-N (CN), were compared to a conventional RBC (Z350) and a resin-modified glass ionomer cement (Fuji-II-LC). Ten disk-shaped specimens were fabricated for each material (n = 40). After standardized surface polishing procedure, the surface properties of the specimens were evaluated using surface roughness measurements by a profilometer and hydrophobicity using water contact angle measurements. To assess bacterial adhesion, the number of S. mutans bacteria was calculated from colony-forming units (CFU). Confocal laser scanning microscope analysis was done for qualitative & quantitative assessment. The data were analyzed using One-way ANOVA followed by Tukey's post-hoc test to compare the mean values of surface roughness, water contact angle and CFU values. To compare the mean dead cell percentage Kruskal-Wallis rank test and Conover test were used. A p-value of ≤ 0.05 was used to report the statistical significance. RESULTS: Z350 and ACT had the smoothest surfaces, followed by CN, and the roughest surface was seen in FUJI-II-LC. The lowest water contact angles were seen in CN, and Z350, and the highest were in ACT. S. mutans counts were the highest in ACT and the lowest in Z350 and CN. CN and Fuji-II-LC registered the highest percentage of dead bacterial cells, while the lowest were in ACT. SIGNIFICANCE: Surface properties did not significantly influence bacterial adhesion. More S. mutans bacteria accumulated on ACT than on the nanofilled composite and on CN. CN had antibacterial effects against Streptococcus mutans biofilms.

Synthesis of ZnO Nanorod-Decorated Graphene Oxide for Application in Dental Resin Composites.

Biofilm formation on resin composite surfaces is associated with the occurrence of secondary caries around restorations. As a promising antibacterial nanomaterial, graphene oxide is effective to suppress the viability of the cariogenic bacteria Streptococcus mutans (S. mutans). However, GO naturally expresses brown, which limits its potential application in dentistry. In this work, ZnO nanorod-decorated graphene oxide (GOn@ZnO) particles were synthesized via a facile hydrothermal method, and their optical property was regulated by changing the amount of seeded GO (n value) in the microemulsion. Among all hybrid particles, GO3@ZnO exhibited a bright gray color and lowest UV absorbance and therefore was selected as an optimal functional filler to produce dental composites with different loadings (0.1, 0.5, 1, and 3 wt %). The effects of GO3@ZnO loading on light transmittance, polymerization conversion, mechanical property, in vitro cell viability, and antibacterial effect of dental composites were systematically explored. The results exhibited that the 0.5 wt % GO3@ZnO-filled composite demonstrated comparable degree of conversion (60 s), higher flexural strength and modulus, and similar cell viability to the control. This composite also effectively inhibited the growth of S. mutans, giving a significantly lower bacterial concentration (3.9 × 107 CFU/mL) than the unfilled resin (8.5 × 107 CFU/mL) and the 0.5 wt % GO-filled composite (6.6 × 107 CFU/mL), respectively. The introduction of GO3@ZnO in dental composites could be a promising strategy to prevent secondary caries and extend service life.

The effect of propolis on the bond strength of composite resin to enamel after intracoronal bleaching with different bleaching agents.

This study evaluated the effect of propolis as an antioxidant agent on bond strength to enamel after intracoronal bleaching. A total of 160 incisors were endodontically treated. Sixteen teeth were served as control, and the remaining teeth were randomly divided into three main groups according to the bleaching agent used; group 1: Sodium perborate (SP); group 2: Carbamide peroxide (CP); group 3: Hydrogen peroxide (HP). After bleaching, the samples were divided into three subgroups; subgroup A: no antioxidant agent application, subgroup B: sodium ascorbate (SA), subgroup C: propolis (PP). After the antioxidant agents application, the sample's surfaces were washed and dried. After adhesive application, composite resin cylinders were applied to enamel surfaces using tygon tubes and a shear bond strength test was performed. The use of PP significantly decreased the bond strength of composite resin to the enamel (p < 0.05). Using propolis as an antioxidant agent adversely affects the bond strength to enamel after intracoronal bleaching.